OM-867
083 696D
December 1993
OWNER’S
MANUAL
Digi-Meter 1500 RMS (AC/DC)
Digital Ammeter/Voltmeter For Measuring Weld Output
Accurately (±1%) Measures DC Or AC (RMS) Output
Max. Capacity: 1500 Amperes, 100 Volts AC/DC At 100% Duty Cycle
Includes 8 ft (2.4 m) 115 Volts AC Input Power Cord
Displays To Nearest Ampere And 1/10 Volt
Has Hold Feature Which Takes Readings After 10 Seconds Of Welding
And Holds Displays For 15 Seconds After Welding Stops
Read and follow these instructions and all
Give this manual to the operator.
safety blocks carefully.
Have only trained and qualified persons
install, operate, or service this unit.
For help, call your distributor
Call your distributor if you do not understand
the directions.
or: MILLER Electric Mfg. Co., P.O. Box 1079,
Appleton, WI 54912
414-734-9821
1993 MILLER Electric Mfg. Co.
cover 7/93 – ST-084 121-A
PRINTED IN USA
ARC WELDING SAFETY PRECAUTIONS
ARC WELDING can be hazardous.
WARNING
PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN
AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR.
In welding, as in most jobs, exposure to certain hazards occurs. Welding is safe when precautions are taken. The
safety information given below is only a summary of the more complete safety information that will be found in the
Safety Standards listed on the next page. Read and follow all Safety Standards.
HAVE ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED ONLY BY
QUALIFIED PEOPLE.
in disconnect box or that cord plug is connected to a properly
groundedreceptacle outlet.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic
wire welding, the wire, wire reel, drive roll housing, and
all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly
groundedequipment is a hazard.
7. When making input connections, attach proper grounding
conductor first – double-check connections.
8. Frequentlyinspect input power cord for damage or bare wiring –
replace cord immediately if damaged – bare wiring can kill.
9. Turn off all equipment when not in use.
10. Do not use worn, damaged, undersized, or poorly spliced cables.
11. Do not drape cables over your body.
1. Do not touch live electrical parts.
12. If earth grounding of the workpiece is required, ground it directly
2. Wear dry, hole-free insulating gloves and body protection.
with a separate cable – do not use work clamp or work cable.
3. Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the
work or ground.
13. Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
4. Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according
to OSHA 29 CFR 1910.147 (see Safety Standards).
14. Use only well-maintained equipment. Repair or replace
damagedparts at once. Maintain unit according to manual.
15. Wear a safety harness if working above floor level.
16. Keep all panels and covers securely in place.
5. Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
6. Always verify the supply ground – check and be sure that input
17. Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
power cord ground wire is properly connected to ground terminal
ARC RAYS
ARC RAYS can burn eyes and skin;
NOISE can damage hearing; FLYING
SLAG OR SPARKS can injure eyes.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays that
can burn eyes and skin. Noise from some processes
can damage hearing. Chipping, grinding, and welds
cooling throw off pieces of metal or slag.
2. Wear a welding helmet fitted with a proper shade of filter to
protect your face and eyes when welding or watching (see ANSI
Z49.1 and Z87.1 listed in Safety Standards).
3. Wear approved safety glasses with side shields.
4. Use protective screens or barriers to protect others from flash
and glare; warn others not to watch the arc.
NOISE
5. Wear protective clothing made from durable, flame-resistant
material(wool and leather) and foot protection.
1. Use approved ear plugs or ear muffs if noise level is high.
5. Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained
watchperson nearby. Welding fumes and gases can displace air
and lower the oxygen level causing injury or death. Be sure the
breathing air is safe.
FUMES AND GASES can be hazardous
to your health.
Welding produces fumes and gases. Breathing these
fumes and gases can be hazardous to your health.
6. Do not weld in locations near degreasing, cleaning, or spraying
operations.The heat and rays of the arc can react with vapors to
form highly toxic and irritating gases.
1. Keep your head out of the fumes. Do not breathe the fumes.
2. If inside, ventilate the area and/or use exhaust at the arc to
remove welding fumes and gases.
3. If ventilation is poor, use an approved air-supplied respirator.
4. Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instruction for metals, consumables, coatings,
cleaners, and degreasers.
7. Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the
weld area, the area is well ventilated, and if necessary, while
wearing an air-supplied respirator. The coatings and any metals
containingthese elements can give off toxic fumes if welded.
4. Never drape a welding torch over a gas cylinder.
5. Never allow a welding electrode to touch any cylinder.
6. Never weld on a pressurized cylinder – explosion will result.
7. Use only correct shielding gas cylinders, regulators, hoses, and
fittings designed for the specific application; maintain them and
associated parts in good condition.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
8. Turn face away from valve outlet when opening cylinder valve.
1. Protect compressed gas cylinders from excessive heat,
mechanical shocks, slag, open flames, sparks, and arcs.
9. Keep protective cap in place over valve except when cylinder is
in use or connected for use.
2. Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
3. Keep cylinders away from any welding or other electrical circuits.
10. Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
sr1.1.1 2/94
6. Be aware that welding on a ceiling, floor, bulkhead, or partition
can cause fire on the hidden side.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks, drums,
or pipes, can cause them to blow up. Sparks can fly off
from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal
objects can cause sparks, explosion, overheating, or
fire. Check and be sure the area is safe before doing
any welding.
7. Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
8. Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
9. Do not use welder to thaw frozen pipes.
1. Protect yourself and others from flying sparks and hot metal.
2. Do not weld where flying sparks can strike flammable material.
3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
4. Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
5. Watch for fire, and keep a fire extinguisher nearby.
10. Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
11. Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
12. Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
ENGINES can be hazardous.
WARNING
ENGINE EXHAUST GASES can kill.
1. Use equipment outside in open, well-ventilated areas.
Engines produce harmful exhaust gases.
2. If used in a closed area, vent engine exhaust outside and away
from any building air intakes.
3. Do not overfill tank – allow room for fuel to expand.
4. Do not spill fuel. If fuel is spilled, clean up before starting
engine.
ENGINE FUEL can cause fire or
explosion.
Engine fuel is highly flammable.
1. Stop engine and let it cool off before checking or adding fuel.
2. Do not add fuel while smoking or if unit is near any sparks or
open flames.
3. Have only qualified people remove guards or covers for
maintenanceand troubleshooting as necessary.
MOVING PARTS can cause injury.
Moving parts, such as fans, rotors, and belts can cut
fingers and hands and catch loose clothing.
4. To prevent accidental starting during servicing, disconnect
negative (–) battery cable from battery.
5. Keep hands, hair, loose clothing, and tools away from moving
parts.
1. Keep all doors, panels, covers, and guards closed and
securely in place.
6. Reinstall panels or guards and close doors when servicing is
finished and before starting engine.
2. Stop engine before installing or connecting unit.
1. Always wear a face shield when working on a battery.
SPARKS can cause BATTERY
GASES TO EXPLODE; BATTERY
ACID can burn eyes and skin.
2. Stop engine before disconnecting or connecting battery
cables.
3. Do not allow tools to cause sparks when working on a battery.
4. Do not use welder to charge batteries or jump start vehicles.
5. Observe correct polarity (+ and –) on batteries.
Batteries contain acid and generate explosive
gases.
1. If the engine is warm and checking is needed, follow steps 2
and 3.
2. Wear safety glasses and gloves and put a rag over cap.
3. Turn cap slightly and let pressure escape slowly before
completely removing cap.
STEAM AND PRESSURIZED HOT
COOLANT can burn face, eyes, and
skin.
It is best to check coolant level when engine is cold
to avoid scalding.
PRINCIPAL SAFETY STANDARDS
Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.
Safety and Health Standards, OSHA 29 CFR 1910, from Superinten-
dent of Documents, U.S. Government Printing Office, Washington, D.C.
20402.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
CanadianStandards Association, Standards Sales, 178 Rexdale Bou-
levard, Rexdale, Ontario, Canada M9W 1R3.
Recommended Safe Practices for the Preparation for Weldingand Cut-
ting of Containers That Have Held Hazardous Substances, American
Welding Society Standard AWS F4.1, from American Welding Society,
550 N.W. LeJeune Rd, Miami, FL 33126
Safe Practices For Occupation And Educational Eye And Face Protec-
tion, ANSI Standard Z87.1, from American National Standards Institute,
1430 Broadway, New York, NY 10018.
NationalElectrical Code, NFPA Standard 70, from National Fire Protec-
Cutting And Welding Processes, NFPA Standard 51B, from National
tion Association, Batterymarch Park, Quincy, MA 02269.
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
sr1.1.1 2/94
EMF INFORMATION
Considerations About Welding And The Effects Of Low Frequency Electric And
Magnetic Fields
NOTE
The following is a quotation from the General Conclusions Section of
the U.S. Congress, Office of Technology Assessment, Biological
Effects of Power Frequency Electric & Magnetic Fields –
Background Paper, OTA-BP-E-53 (Washington, DC: U.S.
GovernmentPrinting Office, May 1989): “. . . there is now a very large
volume of scientific findings based on experiments at the cellular
level and from studies with animals and people which clearly
establish that low frequency magnetic fields can interact with, and
produce changes in, biological systems. While most of this work is
of very high quality, the results are complex. Current scientific
understandingdoes not yet allow us to interpret the evidence in a
single coherent framework. Even more frustrating, it does not yet
allow us to draw definite conclusions about questions of possible risk
or to offer clear science-based advice on strategies to minimize or
avoid potential risks.”
To reduce magnetic fields in the workplace, use the following
procedures:
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around the body.
4. Keep welding power source and cables as far away as practical.
5. Connect work clamp to workpiece as close to the weld as
possible.
About Pacemakers:
The above procedures are among those also normally
recommended for pacemaker wearers. Consult your doctor for
complete information.
mod10.1 4/93
TABLE OF CONTENTS
SECTION 1 – SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 – SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 – INSTALLATION
1
1
3-1.
3-2.
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
SECTION 4 – OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
SECTION 5 – MAINTENANCE & TROUBLESHOOTING
5-1.
5-2.
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
SECTION 6 – ELECTRICAL DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
SECTION 7 – PARTS LIST
Figure 7-1. Complete Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
OM-867D – 12/93
SECTION 1 – SAFETY INFORMATION
mod1.1 2/93
Read all safety messages throughout this manual.
Obey all safety messages to avoid injury.
Learn the meaning of WARNING and CAUTION.
1
2
Safety Alert Symbol
Signal Word
1
2
2
WARNING means possible death
or serious injury can happen.
WARNING
CAUTION
3
4
CAUTION means possible minor
injury or equipment damage can
happen.
ELECTRIC SHOCK can kill.
MOVING PARTS can injure.
• Do not touch live electrical parts.
• Keep away from moving parts.
• Disconnect input power before
• Keep all panels and covers closed
3
Statement Of Hazard And Re-
sult
installing or servicing.
when operating.
4
Safety Instructions To Avoid
Hazard
5
5
6
Hazard Symbol (If Available)
Safety Banner
READ SAFETY BLOCKS at start of
Section 3-1 before proceeding.
WARNING
Read safety blocks for each sym-
bol shown.
6
7
7
NOTE
Special instructions for best oper-
ation – not related to safety.
Turn Off switch when using high frequency.
NOTE
Figure 1-1. Safety Information
SECTION 2 – SPECIFICATIONS
Table 2-1. Meter Specifications
Specification
Description
Type Of Input Power
Input Power Cord With Plug
Voltage Sensing Cord With Clamp
Overall Dimensions
115 Volts AC, 50/60 Hz
8 ft (2.4 m)
21 ft (6.4 m)
See Figure 3-1
Weight
Net: 13.5 lb (6.1 kg); Ship: 15 lb (7 kg)
Max. Capacity At 100% Duty Cycle
1500 Amps At 100 Volts AC/DC
OM-867 Page 1
SECTION 3 – INSTALLATION
WARNING
ELECTRIC SHOCK can kill.
FUMES can be hazardous; LACK OF
FRESH AIR AND PROPER
VENTILATION can be harmful.
• Do not touch live electrical parts.
• Turn Off welding power source and disconnect input
power before inspecting or installing. Stop engine on
welding generator.
• Do not breathe welding fumes.
• Place unit only where there is a good fresh air supply
and proper ventilation.
swarn11.1* 3/93
3-1. Location
Turn Off welding power source.
1
Meter
Place meter on bench, welding
power source, or other convenient
location.
Inches
6
Millimeters
A
B
C
152
295
213
11-5/8
8-3/8
1
A
B
C
ST-084 121-A
Figure 3-1. Overall Dimensions
OM-867 Page 2
3-2. Connection Diagram
WARNING
READ SAFETY BLOCKS at start of
Section 3 before proceeding.
1
2
Welding Power Source
Weld Cable (Customer
Supplied)
Using meter in applications where high-fre-
quency output is used may cause poor arc
starting and unreliable meter readings.
See power source Owner’s Manual
for proper size cable. Keep cable
length between meter and arc as
short as possible for more accurate
readings.
3
4
5
6
7
8
Meter
Access Door
Shunt Terminal
SMAW Electrode Holder
GTAW Torch
Wire Feeder
2
Open access door and connect
weld cable from power source to
either shunt terminal. Connect weld
cable from electrode holder, torch
or wire feeder to other shunt termi-
nal.
1
4
2
Close access door.
9
115 VAC Cord/Plug
OR
10 115 VAC Grounded
Receptacle
Connect input power plug to weld-
ing power source or other 115 VAC
receptacle.
3
11 Voltage Sensing Cord/Clamp
12 Workpiece
8
6
Connect voltage sensing clamp to
workpiece.
7
4
2
10
12
5
11
9
ST-154 610-B / ST-155 327
Figure 3-2. Connection Diagram
OM-867 Page 3
SECTION 4 – OPERATION
WARNING
ELECTRIC SHOCK can kill.
• Always wear dry insulating gloves.
• Insulate yourself from work and ground.
• Do not touch live electrical parts.
ARC RAYS can burn eyes and skin;
NOISE can damage hearing.
• Wear welding helmet with correct shade of filter.
• Wear correct eye, ear, and body protection.
• Keep all panels and covers securely in place.
MOVING PARTS can cause injury.
FUMES AND GASES can be hazardous
to your health.
• Keep away from moving parts.
• Keep all doors, panels, covers, and guards closed
• Keep your head out of the fumes.
and securely in place.
• Ventilate area, or use breathing device.
• Read Material Safety Data Sheets (MSDSs) and
MAGNETIC FIELDS FROM HIGH CUR-
RENTS can affect pacemaker operation.
• Pacemaker wearers keep away.
manufacturer’s instructions for material used.
WELDING can cause fire or explosion.
• Do not weld near flammable material.
• Wearers should consult their doctor before going
near arc welding, gouging, or spot welding opera-
tions.
• Watch for fire; keep extinguisher nearby.
• Do not locate unit over combustible surfaces.
• Do not weld on closed containers.
See Safety Precautions at beginning of manual for ba-
• Allow work and equipment to cool before handling.
sic welding safety information.
swarn6.1 10/91
1
2
3
1
2
InsulatingGloves
Safety Glasses With Side
Shields
3
Welding Helmet
Wear dry insulating gloves, safety
glasses with side shields, and a
weldinghelmet with a correct shade
of filter (see ANSI Z49.1).
sb3.1 10/91
Figure 4-1. Safety Equipment
1
Voltmeter
Displays to nearest 1/10 volt.
Ammeter
Displays to nearest ampere.
Std./Hold Switch
1
2
3
VOLTS
2
HOLD
3
STD.
Use switch to select meters display
function.
AMPS
In Std. (Standard) position, meters
continuously display actual volts/
amps while welding; preset value
while idling.
Example:
STD.
In Hold position, meters measure
volts/amps after 10 seconds of
welding and holds values on dis-
plays for 15 seconds after welding
stops.
OCV
OCV
HOLD
6 0 . 0
5 0 . 0
1 0 0
6 0 . 0
0 0 0
0 0 0
STD.
Hold function does not work when
welding amperage is less than
60 A.
Idling Value
Start Welding Displays New Value Stop Welding
Clears Value
HOLD
OCV
OCV
HOLD
STD.
6 0 . 0
5 0 . 0
5 0 . 0
1 0 0
6 0 . 0
0 0 0
1 0 0
0 0 0
After 10
Seconds
For 15
Idling Value
Start Welding
Displays New Value Stop Welding
Holds Value Seconds Clears Value
ST-154 616
Figure 4-2. Voltmeter/Ammeter And Std./Hold Switch
OM-867 Page 4
SECTION 5 – MAINTENANCE & TROUBLESHOOTING
WARNING
ELECTRIC SHOCK can kill.
HOT PARTS can cause severe burns.
• Do not touch live electrical parts.
• Allow cooling period before maintaining or servicing.
• Turn Off welding power source, and disconnect
input power before inspecting, maintaining, or
servicing. Stop engine on welding generator.
Maintenanceand troubleshooting to be performed only
by qualified persons.
swarn8.1* 10/91
5-1. Routine Maintenance
3 Months
Turn Off all power before maintaining.
6 Months
Blow Out
Replace
Unreadable
Labels
OR
Or
Vacuum
Inside
See
Section
7
– –
Tape Or
Replace
Cracked
Weld
– –
Cable
Clean
And
Tighten
Weld
Terminals
3-2
ST-084 121-A
Figure 5-1. Maintenance Schedule
5-2. Troubleshooting
WARNING
READ SAFETY BLOCKS at start of
Section 5 before proceeding.
Table 5-1. Welding Trouble
Trouble
Remedy
Section
Unit completely inoperative; no meter
display.
Be sure input power cord is plugged in and that receptacle is receiv-
ing input power.
3-2
Incorrect meter display.
Check weld cable, input power, and voltage sensing connections.
Turn off high frequency, if applicable.
3-2
3-2
No display on one meter only; other me-
ter works.
Check connections to meter module; tighten or clean if necessary.
Check and replace meter module if necessary.
– –
– –
– –
Have Factory Authorized Service Station/Service Distributor check
digital meter board PC1.
Erratic meter display.
Check connections to meter shunt; tighten or clean if necessary.
– –
Meters do not hold display with Std./Hold
switch in Hold position.
Place switch in Std. position when welding amperage is below re-
quired minimum.
Figure 4-2
Have Factory Authorized Service Station/Service Distributor check
digital meter board PC1.
– –
OM-867 Page 5
SECTION 6 – ELECTRICAL DIAGRAMS
SB-131 649
Figure 6-1. Circuit Diagram
OM-867 Page 6
SC-132 589
Figure 6-2. Wiring Diagram
OM-867 Page 7
SECTION 7 – PARTS LIST
1
2
7
6
5
4
3
29
28
30
31
8
9
10
29
13
14
15
16
17
18
12
25
26
11
24
27
19
23
28
20
21
22
ST-083 851-D
Figure 7-1. Complete Assembly
OM-867 Page 8
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 7-1. Complete Assembly
. . . 1 . . . . . . . . . . . . . . +082 980 . . . WRAPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . . . . 134 327 . . . LABEL, warning general precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . . . . . . . . . . . 025 248 . . . STAND-OFF, insul .250-20 x 1.250 lg x .437thk . . . . . . . . . . . . . . . . . . . 4
. . . 4 . . . . . Shunt . . . . . 072 425 . . . SHUNT, meter 50MV 1500A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . . 083 082 . . . BUS BAR, jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . 604 126 . . . SCREW, cap stl hexhd .500-13 x 1.000 (connecting cables to
digimeter shunt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . 602 216 . . . WASHER, lock stl split .500 (connecting cables to digimeter shunt) . . 2
. . . . . . . . . . . . . . . . . . . . . . 602 247 . . . WASHER, flat stl SAE .500 (connecting cables to digimeter shunt) . . . 2
. . . . . . . . . . . . . . . . . . . . . . 601 879 . . . NUT, stl hex full .500-13 (connecting cables to digimeter shunt) . . . . . . 2
. . . 6 . . . . C53,54 . . . . 143 461 . . . CAPACITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 7 . . . . . . . . . . . . . . . . 082 983 . . . WRAPPER, shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . . . 600 848 . . . WIRE, lead mot 12ga strd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21ft
. . . 9 . . . . . . . . . . . . . . . . 601 226 . . . INSULATOR, vinyl clamp univ 25A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 10 . . . . . . . . . . . . . . . . 601 228 . . . CLAMP, univ 25A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . PLG50 . . . . 073 690 . . . PLUG, str grd armd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . . . . . . . . . . . 604 825 . . . CABLE, port No. 18 3/c (order by ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8ft
. . . 13 . . . . . . . . . . . . . . . . 131 708 . . . PANEL, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . . . 603 107 . . . HOSE, nprn slit bk .156 ID x .343 OD (order by ft) . . . . . . . . . . . . . . . . . 1ft
. . . 15 . . . . . . . . . . . . . . . . 010 476 . . . BUSHING, strain relief .625 ID x .570mtg hole . . . . . . . . . . . . . . . . . . . . 1
. . . 16 . . . . . . . . . . . . . . . . 131 709 . . . CASE SECTION, bottom/front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 17 . . . . . PC1 . . . . . 132 299 . . . CIRCUIT CARD, digital meter AC/DC models . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . PLG1 . . . . . 135 559 . . . CONNECTOR & SOCKETS, (consisting of) . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 079 747 . . . . CONNECTOR, rect skt 24-18ga Amp 350980-1 . . . . . . . . . . . . . . . . . 12
. . . 18 . . . . . . . . . . . . . . . . 080 509 . . . GROMMET, scr No. 8/10 panel hole .312sq .375 high . . . . . . . . . . . . . . 2
. . . 19 . . . . . . . . . . . . . . . . 131 762 . . . BRACKET, mtg PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 20 . . . . . FL1-3 . . . . . 084 171 . . . FILTER, line pwr 115/250V 50-400Hz at 2A . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 21 . . . . . . . . . . . . . . . . 132 124 . . . STAND-OFF, 6-32 x 1.000 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 22 . . . . . . . . . . . . . . . . 094 484 . . . STAND-OFF, 6-32 x 1.000 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 23 . . . . . . . . . . . . . . . . 019 663 . . . MOUNT, nprn 15/16 OD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . NAMEPLATE, (order by model and style number) . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . C50,51 . . . . 122 723 . . . CAPACITOR, cer mono .1uf 50VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 26 . . . . . D1,2 . . . . . 026 202 . . . DIODE, rect 1A 400V SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 27 . . . . PLG2,3 . . . . 028 598 . . . CONNECTOR, edge 15skt plug Amp 582772-3 . . . . . . . . . . . . . . . . . . . 2
. . . 28 . . . . . Amp . . . . . 083 722 . . . METER, digital 0 to 19.99V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . Volt . . . . . . 081 798 . . . METER, digital 0 to 19.99V LED 115VAC . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 30 . . . . . T50 . . . . . . 131 685 . . . TRANSFORMER, control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 31 . . . . . S50 . . . . . . 011 609 . . . SWITCH, tgl SPDT 15A 125VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-867 Page 9
Notes
OM-867 Page 10
Notes
OM-867 Page 11
Notes
OM-867 Page 12
Effective January 1, 2000
(Equipment with a serial number preface of “LA” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
Warranty Questions?
LIMITED WARRANTY – Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants
to its original retail purchaser that new Miller equipment sold
after the effective date of this limited warranty is free of defects
in material and workmanship at the time it is shipped by Miller.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
*
APT, ZIPCUT & PLAZCUT Model Plasma Cutting
Torches
Call
1-800-4-A-MILLER
for your local
Miller distributor.
*
*
*
*
*
Remote Controls
Accessory Kits
Replacement Parts (No labor)
Spoolmate 185 & Spoolmate 250
Canvas Covers
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be
notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the
warranty claim procedures to be followed.
Your distributor also gives
you ...
Miller’s True Blue Limited Warranty shall not apply to:
1. Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear.
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that
the equipment was delivered to the original retail purchaser, or
one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to an
International distributor.
2. Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Support
3. Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
1. 5 Years Parts – 3 Years Labor
*
*
Original main power rectifiers
Inverters (input and output rectifiers only)
MILLER PRODUCTS ARE INTENDED FOR PURCHASE
AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
2. 3 Years — Parts and Labor
*
*
*
*
*
*
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Semi-Automatic and Automatic Wire Feeders
Inverter Power Supplies
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods
at customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
Intellitig
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by
the engine manufacturer.)
3. 1 Year — Parts and Labor
*
*
DS-2 Wire Feeder
Motor Driven Guns (w/exception of Spoolmate
185 & Spoolmate 250)
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Process Controllers
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources
Water Coolant Systems
HF Units
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
Grids
Maxstar 140
PROVISION,
MIGHT
ARISE
BY
IMPLICATION,
Spot Welders
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL
EQUIPMENT FURNISHED BY MILLER IS EXCLUDED AND
DISCLAIMED BY MILLER.
Load Banks
Miller Cyclomatic Equipment
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Some states in the U.S.A. do not allow limitations of how long
an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
available, but may vary from state to state.
*
Field Options
(NOTE: Field options are covered under True
Blue for the remaining warranty period of the
product they are installed in, or for a minimum of
one year — whichever is greater.)
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations
and exclusions set out above may not apply. This Limited
Warranty provides specific legal rights, and other rights may
be available, but may vary from province to province.
4. 6 Months — Batteries
5. 90 Days — Parts
*
*
MIG Guns/TIG Torches
Induction Heating Coils and Blankets
miller_warr 7/00
Owner’s Record
Please complete and retain with your personal records.
Model Name
Purchase Date
Distributor
Address
Serial/Style Number
(Date which equipment was delivered to original customer.)
City
State
Zip
For Service
to locate a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
International Headquarters–USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
European Headquarters –
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
Welding Process Handbooks
Contact the Delivering Carrier for:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.
PRINTED IN USA
2000 Miller Electric Mfg. Co. 6/00
|