INSTRUCTION MANUAL
Thermoelectric Wine Cooler
MODEL: AW-210ED
Please carefully read and follow all safety rules and operating instructions.
Installation Instructions
Before operating your wine cooler for the first time, follow these steps:
z
z
Remove the exterior and interior packaging.
Check to make sure the following parts are included:
9
9
7 slide-out shelves
1 instruction manual
z
Before connecting the unit to a power source, allow it stand upright for approximately 2 hours.
This will reduce the possibility of any system malfunctions which may have occurred from
handling during transportation.
z
z
Clean the interior surface of the unit with lukewarm water and a soft cloth.
Place the wine cooler on a leveled surface that will be strong enough to support the unit when it is
fully loaded. To level your wine cooler, adjust the front feet located at the bottom of the unit.
Install the wine cooler away from direct sunlight and heat sources such as stoves, heaters, or
radiators, as direct sunlight may affect the unit’s acrylic coating, and nearby heat sources can
increase electrical consumption. Moreover, extreme cold or hot ambient temperatures may also
prevent proper performance.
z
z
PLEASE NOTE: This wine cooler is only designed for home use, and is not designed to be
placed in a garage or basement.
Electrical Connection
To ensure safety and proper operation, please follow the guidelines listed below:
Warning:
Improper use of the grounded plug can result in electrical shock. If the power cord
appears to be damaged, have it replaced by an authorized service center.
•
This wine cooler should be properly grounded for your safety, and in order to minimize the
possibility of electrical shock, the power cord of this unit is equipped with a 3-pin plug which
fits with 3-pin wall outlets.
•
•
•
Never cut or remove the ground wire from the supplied power cord.
The use of extension cords is not recommended.
This unit requires a standard 110V-60HZ electrical outlet with a 3-pin plug. The cord should
be secured behind the wine cooler. Also, to prevent accidental injury, do not expose or dangle
the cord.
Operating Your Wine Cooler
It is recommended that the wine cooler be installed in an area where the ambient temperature is between
10-26
ۦ C (50- 80° F). If the ambient temperature is above or below the recommended ranges, the unit’s performance may be affected, and extreme cold or hot conditions may cause the interior temperature to
fluctuate. This will then prevent the optimal range of 10-16 ° C (50-60° F) from being reached. In
addition, keep in mind that the temperature may fluctuate depending on whether the interior light is on or
off, and whether the bottles are located on the upper, middle, or lower racks.
How to Use the Buttons on the Display Panel:
The desired temperature and light can be set by pressing the buttons on the display panel. The two
buttons on the panel - “ ” and “ ” - adjust the temperature in increments of 1° C between 7-18°
C/10-18° C (44-66° F/54-66° F). You can also turn the interior light on or off by pressing the “Light”
button.
Care and Maintenance
Cleaning Your Wine Cooler
z
Unplug the wine cooler and remove any bottles.
z
Wash the inside of the unit with a warm water and baking soda solution consisting of approximately
2 tablespoons of baking soda to one quart of water.
z
Pull out the water box at the bottom and rinse.
z
To clean the outside of the unit, use a mild detergent and warm water.
Moving Your Wine Cooler
z
z
z
z
z
Remove any bottles.
Securely tape down all loose parts located inside the unit.
Turn the leveling feet up to the base in order to avoid damage.
Tape the door shut.
Be sure the wine cooler stays in an upright position during transportation.
Troubleshooting
To troubleshoot your wine cooler, follow the suggestions below to address the most common problems
before seeking assistance from a service center:
PROBLEM
POSSIBLE CAUSES
The wine cooler will not operate.
•
The unit may be plugged in using a different voltage.
Also, the circuit breaker may be tripped or there is a
blown fuse.
The wine cooler is not cold
enough.
•
Check the temperature control settings, as the external
environment may require a higher setting.
The door may be opened too frequently.
The door is not closed completely.
•
•
•
•
•
•
The door seal does not seal properly.
The wine cooler does not have sufficient clearance.
Contact the dealer or an authorized service center.
Make sure the unit is leveled.
The light does not work.
The wine cooler vibrates while
operating.
The wine cooler produces a lot of
noise.
•
•
•
•
•
•
The unit may not be leveled.
Check the fan.
The door will not close properly.
The unit is not leveled.
The doors are reversed and not properly installed.
The seal is weak.
The shelves are out of position.
The LED display does not work.
•
•
•
•
•
•
There may be a problem with the main control board.
There is a PCB problem.
There is a problem with the plug.
The display may be weak.
There is an LED display error.
The buttons do not function.
The temperature point is off.
The temperature control panel may be damaged.
|