Niles Audio Speaker PHD30 User Manual

I N S T A L L A T I O N G U I D E  
F O R U S E W I T H P L A S M A O R O T H E R F L A T - P A N E L D I S P L A Y  
M U LT I - W AY, H I G H - D E F I N I T I O N , W A L L - M O U N T L O U D S P E A K E R S  
PHD60 PHD42 PHD30  
 
INTRODUCTION  
The Niles PHD60/42/30 High-Definition, Left/Center/Right Channel, Loudspeaker is expressly  
designed for superior sonic quality in front left-, center-, or front right-channel applications. It  
employs advanced technology components that extract the subtle nuances in recorded music or  
the thunderous action sound in a movie. The PHD60/42/30 is the perfect choice wherever quality  
of sound is the most important consideration.  
PHD60  
PHD42  
PHD30  
1
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
 
FEATURES AND BENEFITS  
THREE MODELS DESIGNED FOR USE WITH PLASMA OR  
OTHER FLAT-PANEL DISPLAYS  
The largest model, the PHD60, is designed for use with plasma or other flat-panel displays of  
60-inches or more. The PHD42 complements 42-inch and over displays, while the PHD30 works  
with 30-inches or larger displays. Except for differences in the transducer complement and  
performance, all three models feature similar technologies, For example: the PHD60 and 42 feature  
a 3-way loudspeaker design, while the PHD30 features a 2-way design. All offer voice matching  
sound quality and exceptional detail over a wide listening area.  
5-1/4-INCH TCC WOOFERS WITH CONE-FORWARD™  
DESIGN AND BUTYL-RUBBER SUSPENSION  
The PHD60/42/30 features newly-developed woofer-cone material that combines injection-molded  
polypropylene with talc, carbon, and ceramic (TCC) stiffening agents. As a result, the cone offers  
extreme stiffness and light weight for accurate, dynamic response. Our patent-pending Cone  
Forward™ design positions the woofer cone at the front of the baffle for natural-sounding bass  
and clear, open midrange response. Additionally, the use of a butyl-rubber suspension offers  
substantial benefits, including increased movement without mechanical limitations, and improved  
midrange damping for better detail and clarity.  
1-1/2-INCH FLUID-COOLED TETERON HYPERBOLIC-  
DOME MIDRANGE DRIVER  
The PHD60 and PHD42 also feature a Fluid-Cooled Teteron Hyperbolic-Dome Midrange Driver that  
provides high sound pressures to reproduce critical mid frequencies with exceptional accuracy.  
1-INCH FLUID-COOLED TETERON TRI-LAMINATE TWEETER  
The PHD60/42/30’s Fluid-Cooled Teteron Tweeter employs a tri-laminate design consisting of  
an inner textile layer, which forms the dome, a high damping layer to eliminate unwanted  
resonances, and an outside layer of urethane to add stiffness and prevent breakup modes. The  
result is a transparently clear, sweet, natural-sounding tweeter, which still maintains extended  
frequency response.  
2
 
ADJUSTABLE, DISPERSION-CONTROLLING MIDRANGE/  
TWEETER POD ENABLES PRECISE IMAGING  
The PHD60 and PDH42 each feature a unique Midrange/Tweeter pod that can be rotated and  
pivoted to enable precise imaging regardless of placement. The pod accommodates vertical or  
horizontal installations and can be set by the installer after each loudspeaker is mounted. Included  
are variable treble and midrange level controls for additional response contouring.  
NILES’ HD HIGH-DEFINITION VOICE MATCHING  
Ensures compatibility with other Niles HD High-Definition in-wall, on-wall, and ceiling-mount  
models to accommodate a wide range of system designs.  
ADVANCED BASS-REFLEX DESIGN FOR ENHANCED  
DYNAMIC IMPACT  
The PHD60/42/30’s bass-reflex design enhances low-frequency response and dynamic impact.  
Moreover, the rigid extruded aluminum enclosure helps deliver accurate bass response with  
low distortion.  
LOOKS GREAT AND EASY TO INSTALL  
The PHD60/42/30’s contemporary finish matches popular flat-panel displays, and its integrated  
wall mount brackets make installation quick and easy.  
DOLBY® DIGITAL READY  
The PHD60/42/30 is specifically designed for Home Theater Sound. They are designed to  
complement and provide for the accurate reproduction of Dolby Digital Encoded Sources.  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
3
 
INSTALLATION CONSIDERATIONS  
WALL MOUNTING  
The Niles PHD60/42/30 loudspeaker is equipped with an included wall-mount bracket for quick  
and easy installation on a wall. Ideally, a PHD60/42/30 should be placed so that its bracket can  
be installed on underlying wall studs. If stud mounting is impractical, dry-wall anchors (rated for  
at least 40 pounds) can be used to mount the loudspeaker between studs (see INSTALLING THE  
WALL-MOUNT BRACKETS on page 7).  
RECOMMENDED AMPLIFIER POWER  
For satisfactory performance, we recommend using a home theater receiver (or amplifier) with  
a power rating of 10 to 250 watts for the PHD60,10 to 200 watts for the PHD42, and 10 to 150  
watts for the PHD30. Most loudspeakers are not damaged by large amplifiers, but rather by small  
amplifiers. If your system is playing loud music, a small amplifier will run out of power very quickly  
and can create damaging “clipping” distortions. A more powerful amplifier will play at the same  
volume without distorting. See OPERATION on page 13 for more information about amplifier  
clipping distortion.  
LOUDSPEAKER WIRE  
Use 2-conductor loudspeaker wire when connecting loudspeakers to your receiver or amplifier.  
For most applications, we recommend using 16- or 18-gauge wire. For wiring runs longer than  
80 feet, we recommend 14-gauge wire. The spring-loaded terminals of the PHD60/42/30 will  
accommodate up to 12-gauge wire directly. Larger sizes can be accommodated via  
pin connectors.  
When running wire inside walls or ceilings, always use (CL-2 or CL-3) rated cable. In some areas,  
conduit is also required. For a trouble-free installation, low-voltage wire such as loudspeaker wire  
must be run in accordance with the National Electrical Code and any applicable provisions of the  
local building code. If you are unsure of the correct installation techniques, wire jacket, or type of  
conduit to use, consult a professional audio/video installer, building contractor, or the local building  
and inspection department.  
TECH TIP  
Wire size is expressed by its AWG (American  
Wire Gauge) number – the lower the number,  
the larger the wire. For example, 12 AWG is  
physically larger than 14 AWG.  
4
 
LOUDSPEAKER PLACEMENT  
The Niles PHD60/42/30 loudspeaker is designed for use in front left-, center-, or front right-  
channel applications. Any model can be wall-mounted using its included wall-mount bracket.  
For rear-channel applications, we recommend using a Niles HD FX or CM6HDfx loudspeaker.  
PLACING PHD60/42/30’S AS THE FRONT LEFT AND  
RIGHT LOUDSPEAKERS  
In a home theater, the intelligibility of dialog and action reproduced by the front speakers is  
paramount! The position of the loudspeakers plays a very important role in how clear the sound is  
and how a stereo image is created.  
The PHD60/42/30’s are designed specifically for use with plasma or flat-panel displays in a home  
theater system. The placement process is quick and easy:  
• At the proposed site, make sure the sound will not be blocked or reflected off furniture  
or other objects. The listener should have a direct line of sight with the front of each  
loudspeaker. The ideal listening position (e.g., favorite chair or couch) should be  
centered with the middle of plasma or flat-panel display  
• Place the speakers with the ports on the bottom on either side of display, as shown  
in Figure 1 (also see INSTALLING THE WALL-MOUNT BRACKETS on page 7). In  
applications where there is a center channel, you may choose to space the left and  
right main speakers farther apart for a “bigger than life” sound with Dolby® encoded  
movies and TV shows.  
Aim midrange and  
tweeter towards  
listener  
Figure 1.  
Recommended PHD60  
Critical  
Listening  
Position  
loudspeaker placement  
for front left and right  
channels is shown  
Plasma TV  
here. Placement of the  
PHD42/30 is similar.  
Aim midrange and  
tweeter towards  
listener  
(CONTINUED ON NEXT PAGE)  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
5
 
PLACING PHD60/42/30’S AS THE FRONT LEFT AND RIGHT  
LOUDSPEAKERS (CONTINUED)  
• As for placement height, place front left and right speakers vertically on either side  
of the display, so that their tweeters are not more than 24 inches above or below the  
center-channel loudspeaker’s tweeter (see Figure 2 below).  
PLACING A PHD60/42/30 AS THE CENTER-CHANNEL  
LOUDSPEAKER  
The center-channel loudspeaker is the workhorse in a home theater system. It handles all of the  
critical dialog and is vitally important in creating the illusion of sounds emanating directly from the  
picture. Here are some tips for obtaining optimum center-channel performance:  
Figure 2.  
Not Greater  
than 24"  
Recommended PHD60  
loudspeaker placement  
for the center channel is  
shown here. Placement of  
the PHD42/30 is similar.  
Not Greater  
than 24"  
• In a typical installation, place the PHD60/42/30 horizontally, directly above or below the  
plasma or flat-panel display. Make sure the loudspeaker is not placed too high or low  
relative to the left and right speakers, as shown in Figure 2.  
• For installations where a perforated projection  
Perforated Screen  
screen will be used, place the PHD60/42/30  
with grille removed, either horizontally or  
vertically, behind the screen at ear level,  
as shown in Figure 3.  
Figure 3. Recommended PHD60 center-channel  
placement with grille removed behind a perforated  
projection screen is shown here. Placement of the  
PHD42/30 is similar.  
6
 
INSTALLING THE WALL-MOUNT BRACKETS  
TOOLS AND PARTS  
We recommend using the following tools and parts to install the PHD60/42/30 wall-mount brackets:  
• Electric drill and drill bits  
• Philips screwdrivers or driver bit set  
• Stud finder  
• Eight wood screws with (optional) dry-wall anchors rated for at least 40 pounds  
• Pencil  
• Level  
• Protective eyewear  
PRECAUTIONS  
Before starting the installation, please observe the following precautions:  
• Turn off all system power before making any connections.  
• Always wear protective eyewear when using tools.  
• Make sure hands are clean before installation.  
• Wear gloves when working with fiberglass insulation.  
INSTALLATION  
1. At each proposed site, use a stud finder to locate studs (which should be on 16-inch  
centers) for possible use in the installation. If the studs do not line up with a desired  
placement location, the PHD60/42/30 wall-mount bracket can still be mounted on a dry  
wall with appropriate dry-wall screws and anchors.  
IMPORTANT: DO NOT USE PLASTIC EXPANSION OR THREADED WALL ANCHORS FOR DRY  
WALL INSTALLATION. CONSULT YOUR LOCAL NILES DEALER OR HOME HARDWARE STORE  
FOR RECOMMENDATIONS FOR YOUR HOME THEATER APPLICATION.  
(CONTINUED ON NEXT PAGE)  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
7
 
INSTALLATION (CONTINUED)  
2. For each loudspeaker, orient and tape the enclosed mounting template to the wall  
at the desired placement location, as shown in Figure 4. Use a level to verify tilt  
is zero. Be sure to account for any moldings that may interfere with the loudspeaker  
cabinet upon installation.  
Bracket Template  
Figure 4. The PHD mounting template is shown in  
horizontal and vertical positions (with TOP side up).  
3. Follow the directions included on the template. Drill four small mounting holes at the  
designated locations noted on the template. If you also plan to run loudspeaker wire  
in the wall, you’ll need to create a cutout for it within the noted wire boundary (see  
Figure 4). When drilling is complete, remove each mounting template.  
4. Use the stamped (TOP) label to orient each mounting bracket and run loudspeaker  
wire through its opening for later connection. Fasten each bracket to the wall with  
appropriate mounting hardware.  
8
 
FINISHING THE INSTALLATION  
CONNECTING THE LOUDSPEAKER  
1. At each loudspeaker, separate the loudspeaker wire so that at least 2 inches of each  
conductor are free. Strip away 1/4 inch of insulation from each loudspeaker wire.  
2. On each set of loudspeaker connectors, press down the spring-loaded lever, insert the  
appropriate conductor, and then release the lever, as shown in Figure 5. Gently tug  
on the loudspeaker wire to make sure it is held in place. If not, repeat this procedure  
until it is. Make sure that only the bare wire is clamped in the connector.  
NOTE: OBSERVE CORRECT POLARITY: POSITIVE (+) GOES INTO THE RED TERMINAL AND  
NEGATIVE (–) GOES INTO THE BLACK TERMINAL. IF YOU ARE UNSURE OF WIRE POLARITY, SEE  
THE SECTION CHECKING LOUDSPEAKER PHASE ON PAGE 11.  
Figure 5. Connecting  
a loudspeaker wire to the  
PHD60/42/30 terminals.  
3. If a mounting bracket was installed  
on the wall, align each loudspeaker  
with the two mounting holes (on its  
bracket) and let it slide down into the  
keyslot on the bracket to fasten it to  
the wall, as shown in Figure 6.  
Figure 6. Installing a PHD60/42/30 loudspeaker  
onto its mounting bracket.  
(CONTINUED ON NEXT PAGE)  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
9
 
CONNECTING THE LOUDSPEAKER (CONTINUED)  
4. Connect the other end of the loudspeaker wires to the home theater receiver (or  
amplifier) in the same way as steps 1 and 2.  
5. Turn on the home theater receiver and calibrate all loudspeakers in the system  
according to the receiver manufacturer’s instructions.  
PHD60/42: SETTING THE TWEETER/MIDRANGE POD  
Each PHD60/42 features an adjustable Tweeter/Midrange Pod on the front baffle for proper  
loudspeaker orientation and precise imaging, as shown in Figure 7. Adjust the pod as follows:  
Figure 7. Each PHD60/42 includes an adjustable Tweeter/Midrange Pod that can be rotated up  
to 90 degrees for proper loudspeaker orientation and pivoted for precise imaging.  
• For a vertical installation, no adjustments are required. The Tweeter/Midrage pod is  
optimally set at the factory for this placement.  
• For a horizontal installation (e.g., center-channel application), perform the following  
steps to rotate the Tweeter/Midrage pod:  
1. Using the enclosed Allen wrench, remove the four (4) Allen-head screws,  
(see Figure 7).  
2. Gently pull the pod away from the enclosure and rotate it 90° in either direction (see  
Figure 7). Be careful not to disconnect any attached wires during rotation.  
3. Place the pod back into the enclosure and reinstall the four (4) Allen-head screws.  
• If desired, after vertical or horizontal installation, set the imaging by pressing the pod’s  
edge to aim the drivers at the listening position (see Figure 7).  
10  
 
PHD60/42: ACOUSTIC FINE TUNING  
Each PHD60/42 also features variable TREBLE and MIDRANGE controls on the front baffle for  
acoustic fine-tuning after placement, as shown in Figure 8. Adjust these controls as follows:  
Figure 8. Each PHD60/42 includes variable  
TREBLE and MIDRANGE controls with up to 3 dB of  
boost or cut in the response.  
• Initially set both TREBLE and MIDRANGE control to 0 dB.  
• If a PHD60/42 is placed in a room with highly reflective surfaces like glass or tile or  
the reproduced sound is too bright, decrease the TREBLE setting by as much as –3 dB  
to lower the high-frequency response. If the room has heavy drapes or is wallpapered,  
try increasing the TREBLE setting by as much as +3 dB to brighten the  
high-frequency response.  
• Listen to dialog being reproduced on the PHD60/42. If you want it more pronounced,  
increase the MIDRANGE setting by as much as +3 dB to enhance the mid-frequency  
response. If the dialog is too pronounced, decrease the MIDRANGE setting by as much  
as –3 dB to lower the mid-frequency response.  
CHECKING LOUDSPEAKER PHASE  
Loudspeaker wire has two conductors. On both your loudspeaker and amplifier, one conductor  
is attached to the negative (–) terminals, while the other is attached to the positive (+) terminals.  
Usually, the wire is marked for your convenience, but the marking can be done in the following  
different ways:  
• Stripe on one wire  
• Ribbed area you can feel on one conductor  
• Different colors of metal wire on each conductor  
• Fabric strand or string wound into one of the conductors  
(CONTINUED ON NEXT PAGE)  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
11  
 
CHECKING LOUDSPEAKER PHASE (CONTINUED)  
Of course, there are some wires that appear completely identical. So be careful, or you might make  
a connection mistake. If you do, one loudspeaker will be playing “out-of-phase” with the other  
loudspeaker. A pair of out-of-phase loudspeakers works against each other, and the sound of the  
two playing together will be lacking in bass and sound “phasey.” If you suspect the sound is not  
right, and you cannot see any markings on the wire, try this simple test:  
1. Stand halfway between the loudspeakers.  
2. Play some music with the amplifier or receiver set to Mono.  
3. Listen to the richness of the bass and the loudness of the sound.  
4. Turn off the amplifier and reverse the connections on one amplifier channel only.  
5. Repeat the listening test with the same volume control setting. When the sound has a  
richer bass and is slightly louder, the loudspeakers are working together or “in-phase.”  
INSTALLING THE GRILLE  
If desired, at each loudspeaker, carefully fit the grille to its cabinet. Starting with one corner, gently  
press the grille frame around the loudspeaker’s edge, pushing it in at each of the recessed holes.  
12  
 
OPERATION  
LISTENING AT HIGHER VOLUMES  
Achieving a reasonable volume of sound in a large room requires more amplifier power than it  
does in a small room. It is possible to turn the volume up so high that the amplifier runs out of  
power. This creates “clipping” distortion, which will make treble sound very harsh and unmusical.  
When you hear harsh-sounding treble from any good loudspeaker, turn the volume down  
immediately! Those harsh sounds are masking much more powerful ultra-high-frequency sound  
spikes, which will quickly damage any fine loudspeaker. You are much less likely to damage a  
loudspeaker driven by a large amplifier because it will be very loud before any clipping  
distortion is produced.  
CLEANING  
To clean the enclosure, use a dampened soft cloth or paper towel. To clean the grille, use a gentle  
vacuum cleaner.  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
13  
 
SPECIFICATIONS  
PHD60  
PHD42  
PHD30  
Driver Complement  
• Four 5-1/4" TCC Woofers  
• 1-1/2" Teteron Midrange  
with fluid cooling  
Driver Complement  
• Four 5-1/4" TCC Woofers  
• 1-1/2" Teteron Midrange  
with fluid cooling  
Driver Complement  
• Two 5-1/4" TCC Woofers  
• 1" Teteron Tweeter with  
fluid cooling  
• 1" Teteron Tweeter with  
fluid cooling  
• 1" Teteron Tweeter with  
fluid cooling  
Design Principle  
• Bass-reflex design  
• 3-way crossover for  
optimum phase and  
frequency response  
• Adjustable, dispersion-  
controlling, midrange/  
tweeter pod  
Design Principle  
• Bass-reflex design  
• 3-way crossover for  
optimum phase and  
frequency response  
• Adjustable, dispersion-  
controlling, midrange/  
tweeter pod  
Design Principle  
• Bass-reflex design  
• 2-way crossover for  
optimum phase and  
frequency response  
• Symmetrical driver  
configuration for dispersion  
control and precise imaging  
Recommended Amplifier  
Power  
10 to 250 watts per channel  
Recommended Amplifier  
Power  
10 to 200 watts per channel  
Recommended Amplifier  
Power  
10 to 150 watts per channel  
Nominal Impedance  
4 ohms  
Nominal Impedance  
4 ohms  
Nominal Impedance  
4 ohms  
Frequency Response  
55 Hz to 21 kHz, +/- 3 dB  
Frequency Response  
63 Hz to 21 kHz, +/- 3 dB  
Frequency Response  
70 Hz to 21 kHz, +/- 3 dB  
Sensitivity  
Sensitivity  
Sensitivity  
90 dB with 2.83 V pink noise  
input, measured at 1 meter  
on axis  
89 dB with 2.83 V pink noise  
input, measured at 1 meter  
on axis  
89 dB with 2.83 V pink noise  
input, measured at 1 meter  
on axis  
Dimensions (with Wall  
Bracket)  
34.7" H x 6.2" W x 5.6" D  
Dimensions (with Wall  
Bracket)  
24.8" H x 6.2" W x 5.6" D  
Dimensions (with Wall  
Bracket)  
19.6" H x 6.2" W x 5.6" D  
Weight  
40 lb  
Weight  
30 lb  
Weight  
20 lb  
Wiring Requirements  
Wiring Requirements  
Wiring Requirements  
We recommend using 16- to  
18-gauge loudspeaker wire  
for runs up to 80 feet and  
14-gauge loudspeaker wire  
for runs up to 200 feet. The  
connectors will accommodate  
12- to 22-gauge wire.  
We recommend using 16- to  
18-gauge loudspeaker wire  
for runs up to 80 feet and  
14-gauge loudspeaker wire  
for runs up to 200 feet. The  
connectors will accommodate  
12- to 22-gauge wire.  
We recommend using 16- to  
18-gauge loudspeaker wire  
for runs up to 80 feet and  
14-gauge loudspeaker wire  
for runs up to 200 feet. The  
connectors will accommodate  
12- to 22-gauge wire.  
14  
 
NOTES  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI  
15  
 
LIMITED WARRANTY  
NILESAUDIOCORPORATION(“NILES”)WARRANTSITSLOUDSPEAKERPRODUCTSTOTHEORIGINALPURCHASERTO  
BE FREE OF MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF TWO YEARS FROM  
DATE OF PURCHASE.  
THIS WARRANTY IS SUBJECT TO THE FOLLOWING ADDITIONAL CONDITIONS AND LIMITATIONS. THE WARRANTY  
IS VOID AND INAPPLICABLE IF NILES DEEMS THAT THE PRODUCT HAS BEEN USED OR HANDLED OTHER THAN IN  
ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER, INCLUDING BUT NOT LIMITED TO  
DAMAGE CAUSED BY ACCIDENT, MISHANDLING, IMPROPER INSTALLATION, ABUSE, NEGLIGENCE, OR NORMAL  
WEAR AND TEAR, OR ANY DEFECT CAUSED BY REPAIR TO THE PRODUCT BY ANYONE OTHER THAN NILES OR AN  
AUTHORIZED NILES DEALER.  
TO OBTAIN WARRANTY SERVICE, TAKE THE UNIT TO THE NEAREST AUTHORIZED NILES DEALER, WHO WILL  
TEST THE PRODUCT AND IF NECESSARY, FORWARD IT TO NILES FOR SERVICE. IF THERE ARE NO AUTHORIZED  
NILES DEALERS IN YOUR AREA, YOU MUST WRITE TO NILES AND INCLUDE YOUR NAME, ADDRESS, MODEL AND  
SERIAL NUMBER OF YOUR UNIT, ALONG WITH A BRIEF DESCRIPTION OF THE PROBLEM. A FACTORY RETURN  
AUTHORIZATION NUMBER WILL BE SENT TO YOU. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN  
AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES.  
IF THE ABOVE CONDITIONS ARE MET, THE PURCHASER’S SOLE REMEDY SHALL BE TO RETURN THE PRODUCT TO  
NILES, IN WHICH CASE NILES WILL REPAIR OR REPLACE, AT ITS SOLE OPTION, THE DEFECTIVE PRODUCT WITHOUT  
CHARGE FOR PARTS OR LABOR. NILES WILL RETURN A UNIT REPAIRED OR REPLACED UNDER WARRANTY BY  
SHIPPING SAME BY ITS USUAL SHIPPING METHOD FROM THE FACTORY (ONLY) AT ITS EXPENSE WITHIN THE  
UNITED STATES OF AMERICA. THERE ARE NO OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION, EITHER  
EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH  
RESPECT TO THE PRODUCT.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER/  
PURCHASER. NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO  
THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND  
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.  
FOR THE NAME OF YOUR NEAREST AUTHORIZED NILES DEALER CONTACT:  
NILES AUDIO CORPORATION, P.O. BOX 160818, MIAMI, FLORIDA 33116-0818.  
Please fill in your product information and retain for your records.  
Model______________________ Serial No.___________________ Purchase Date_______  
16  
 
WARRANTY REGISTRATION CARD  
Model Purchased_________________________________________________________  
Serial Number ___________________________________________________________  
Date Purchased (month/day/year)_____________________________________________  
Dealer Name and Location __________________________________________________  
______________________________________________________________________  
Dr.  
Miss  
Mr.  
Mrs.  
Ms.  
Name__________________________________________________________________  
Address________________________________________________________________  
______________________________________________________________________  
City_______________________________________State________________Zip______  
Telephone (  
) _________________________________________________  
Please take a moment to fill out our warranty registration card. The information helps us to get to  
know you better and develop the products you want  
Age:  
Musical tastes:  
(Please check  
all that apply)  
What magazines  
do you read?  
Do you . . . ?  
Under 25  
Own a House. If yes,  
25-34  
1. ________________  
how many square feet?  
35-44  
Alternative  
2. ________________  
3. ________________  
45-54  
55 & over  
Classical  
Country  
Own a Town House/  
Jazz  
Condominium/Co-op  
Income:  
New Age  
Rent an Apartment  
Rent a House  
Who will install  
the product?  
Under $24,999  
Popular  
$25,000-$34,999  
$35,000-$44,999  
$45,000-$59,999  
$60,000-$74,999  
$75,000-$99,999  
Over $99,999  
R&B  
Custom Installer  
Rock  
Are you interested in  
receiving literature on  
other Niles products?  
Electrician  
Other _____________  
Friend  
Myself  
How did you hear  
about Niles?  
Yes  
No  
Which factor(s) influenced  
the purchase of your Niles  
product? (Please check  
all that apply)  
Architect/Developer  
Are there products/  
capabilities that you would  
like to see introduced?  
Occupation:  
Custom Installer  
Arts/Entertainment  
Direct Mail  
Business Owner  
Friend/Family  
Ease of Use  
Engineer  
In-Store Display  
Price/Value  
Finance/Accounting  
Interior Designer  
Product Features  
General Office  
Magazine Ad  
Quality/Durability  
Management  
Mail-Order Catalog  
Reputation  
Professional  
Newspaper Ad  
Style/Appearance  
Sales/Marketing  
Product Brochure  
Warranty  
Student  
Product Review  
Tradesperson  
Retail Salesperson  
 
®
BL E N D I N G HI G H FI D E L I T Y AN D AR C H I T E C T U R E  
N i l e s A u d i o C o r p o r a t i o n  
1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6  
D e s i g n e d a n d E n g i n e e r e d i n U S A  
M a d e i n C h i n a  
©2005 Niles Audio Corporation. All rights reserved. Niles, the Niles logos and Blending  
High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. All other trademarks are  
the property of their respective owners. 10/05 DS00413BCN  
 

Miele Microwave Oven 09 919 100 User Manual
Milwaukee Grinder Bench Grinder User Manual
Musical Fidelity Stereo Receiver X V8 User Manual
National TV Converter Box ADC12V170 User Manual
New Holland Lawn Mower G4010 User Manual
Nextar GPS Receiver ME User Manual
Nortel Networks Telephone X 6000 User Manual
Olympus Double Oven VN 1800 User Manual
Olympus Microscope Magnifier PM10SP User Manual
Panasonic Fan 3115PS User Manual