Niles Audio Universal Remote R 6L User Manual

I N S T A L L A T I O N & O P E R A T I O N G U I D E  
HAND-HELD LEARNING REMOTE CONTROL  
R-6L R-8L  
 
INTRODUCTION  
The Niles R-6L and R-8L hand-held learning remote controls are used as source controllers for  
Niles MultiZone receivers (ZR-4 and ZR-6 respectively). They come preloaded with ZR-4/ZR-6,  
ZR-PRO and many other popular component commands, and can learn virtually any IR code for  
enhanced source operation from any zone.  
Figure 1. Niles R-8L Hand-Held Learning Remote Control  
1
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
 
PARTS GUIDE  
1) SOURCE SELECT KEYS  
1.) Pressing one of these keys selects the built-in AM/FM tuner or any of the connected sources  
for playback and operation (for the ZR-4, up to three connected sources, SRC 2-4; and for the  
ZR-6/ZR-PRO up to five connected sources, SRC 2-6 with iPod® always appearing as source  
2.) There are additional Source Select Keys to operate a TV and an auxiliary component such as  
a DVD player connected to the TV.  
2) ON AND OFF KEYS  
Turns the selected device On or Off  
3) SETUP KEY  
Used to configure the remote  
4) TRANSPORT KEYS  
Used to skip backward, rewind, fast forward, skip forward, stop, pause, or play tracks from the  
selected source  
5) MENU KEY  
Press this key to display a menu for the selected source  
6) INFO KEY  
Press this key to display the current channel and program information  
7) MENU CURSOR KEYS  
Use these keys to move the cursor in the menu screen. Press OK to choose the highlighted menu  
option or to toggle between the AM and FM tuner bands  
8) VOLUME KEYS  
These keys are used to raise or lower the sound level. Press the Mute key to turn the sound off or  
on  
9) CHANNEL SELECT KEYS  
These keys are used to select the next or previous channel and to select next or previous chapter  
on some models of DVD players. Press the Last key to recall the last-viewed channel  
10) GUIDE KEY  
Press this key to display the program guide for the selected source  
2
 
11) EXIT KEY  
Press this key to exit the selected source’s menu, guide, or program without making a menu  
selection  
12) DIRECT ACCESS KEYS  
Directly enter channels (for example: 09 or 31). Press the Enter key to send channel number entry on  
certain TV models  
13) EXTENDED FUNCTION KEYS  
Provide additional functionality for advanced features, menus, and guides  
14) DVR SPECIAL FUNCTION KEYS  
3
2
 
�  
 
1
 
 
��  
 
 
 
 
 
4
6
7
5
�  
 
10  
 
 
 
 
9
 
8
�  
�  
11  
14  
12  
 
 
13  
 
 
 
�  
�  
 
 
�  
 
 
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
3
 
BATTERY INFORMATION  
Your Niles R-6L or R-8L Hand-Held Learning Remote Control requires 2 Alkaline “AA” batteries  
(included).  
BATTERY USE AND SAFETY  
• Use only fresh batteries of the required size and recommended type  
• Do not mix old and new batteries, different types of batteries (standard, alkaline, or  
rechargeable), or rechargeable batteries of different capacities  
• If you do not plan to use the remote for an extended period, remove the batteries. They can  
leak chemicals that can destroy electronic parts  
WARNING: DISPOSE OF OLD BATTERIES PROMPTLY AND PROPERLY. DO NOT BURN OR BURY  
THEM.  
TO INSTALL BATTERIES  
1. Open the battery compartment cover (located on the back of the remote).  
2. Place the “AA” batteries in the compartment matching the + and polarity symbols inside.  
3. Replace the cover.  
NOTE: WHEN THE BATTERY VOLTAGE IS LOW, A SOURCE KEY LED WILL BLINK 5 TIMES  
AFTER A KEYPRESS.  
CONFIGURATION  
CONFIGURE A SOURCE  
To configure the Niles R-6L/R-8L Hand-Held Learning Remote Control to control the connected  
source devices, follow the steps below. Before proceeding, find the codes for the devices you want  
to configure in “Manufacturer’s Codes” and write them down or highlight them.  
1. Turn on the device (for example: CD player) and, if needed, load media (for example: a CD).  
2. Press a Source key (SRC2, SRC3, SRC4, SRC5, SRCL or optionally the TV, Aux) on the  
R-6L or R-8L that you wish to program.  
3. Press and hold SETUP until the source key LED blinks twice, then release.  
4
 
4. Enter the first five-digit code for the device and brand that you wish to program. The  
source key LED blinks once as each digit is entered. If the code is valid, source key the  
LED blinks twice.  
NOTE: IF THE SOURCE KEY LED DOES NOT BLINK TWICE, REPEAT STEPS 2 TO 4 AND TRY  
ENTERING THE CODE AGAIN.  
5. Aim the remote at the device and press POWER OFF. The device should turn Off. If it  
does not, repeat steps 3–5, trying each code for your brand until you find one that  
works. If you cannot find a code that works, see “SEARCHING FOR YOUR CODE”.  
6. Repeat steps 1 to 5 for the other devices you want to control.  
SEARCHING FOR YOUR CODE  
If your device does not respond to the remote after trying all codes listed for your brand, or if your  
brand is not listed, try searching for your code:  
1. Turn the device you wish to control on.  
2. Press a source key once.  
3. Press and hold SETUP until the source key LED blinks twice, then release.  
4. Enter 991, then the device group number (see table below). The source key LED blinks twice.  
TABLE:  
0
1
2
Cable (cable converters, video accessories, satellite receivers)  
TV (TVs)  
VCR (VCRs, DVD players )  
3
Audio (audio amplifiers, audio amp/tuners, CD players)  
5. Aim the remote at the device and press POWER OFF. The remote sends IR codes from  
its library to the selected device, starting with the most popular code first. If the  
device responds, go to step 7.  
6. If the device does not respond, press CH+ and the remote will test the next code for  
that device type. Continue to press CH+ until the device turns Off.  
NOTE: PRESS CH- TO TRY THE PREVIOUS CODE.  
7. Now that you have found the correct code, press SETUP to save the code that worked  
for your device. The source key LED will blink twice to indicate that the code has been  
saved. To search for other device codes, repeat steps 1 to 5.  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
5
 
CHECKING THE CODES  
If you have set up the remote using the procedure in “SEARCHING FOR YOUR CODE”, you may  
need to find out which five-digit code is operating your equipment. For example, to find out which  
code is assigned to your TV:  
1. Press TV source key once  
2. Press and hold SETUP until the red LED blinks twice, then release  
3. Enter 9 9 0. The source key LED blinks twice  
4. To view the code for the first digit, press 1. Count the source key LED blinks (for  
example: three blinks = 3), and write down the number.  
NOTE: IF A CODE DIGIT IS 0, THE SOURCE KEY LED DOES NOT BLINK  
5. Continue through the four remaining digits by pressing the 2 key for the second digit, the  
3 key for the third digit, the 4 key for the fourth digit and the 5 key for the fifth digit.  
6. To check for other device codes, repeat steps 1—5, substituting the source key for  
the desired device you would like to check  
LEARNING PRECAUTIONS  
Your original remote controls must be in working order to learn IR commands properly.  
• Learned keys are device-specific, so each key can store a ‘unique function’ for  
each device  
• Do not use the following keys for learning: Source Keys, SETUP  
• Learning capacity is approximately 42 to 75 keys, depending on the code being learned  
• Certain device functions can not be learned including multi-frequency types, some  
high frequency codes, and other unusual formats  
• For optimum learning, avoid high levels of ambient light such as natural sunlight or  
energy-efficient fluorescent lights  
NOTE: PLEASE HAVE YOUR ORIGINAL REMOTE CONTROLS HANDY BEFORE PROGRAMMING LEARNING  
PROGRAMMING A LEARNED KEY  
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE REMOTE EXITS  
PROGRAMMING MODE  
1. Place the Niles R-6L or R-8L Hand-Held Learning Remote Control head-to-head  
(about 2” apart) from your original remote control. Also locate the key (on your original  
6
 
remote control) that you want the R-6L or R-8L Hand-Held Learning Remote Control  
to learn. Press the source key for which you wish to learn keys.  
2. Press and hold SETUP until the source key LED blinks twice, then release.  
3. Enter 9 7 5. The source key LED blinks twice.  
NOTE: IF THE SOURCE KEY LED DISPLAYS ONE LONG FLASH INSTEAD, YOUR BATTERIES ARE LOW, OR THE  
HAND-HELD LEARNING REMOTE CONTROL HAS NO FREE MEMORY SPACE AVAILABLE. IN EITHER CASE, THE  
REMOTE CANNOT LEARN A NEW KEY. REPLACE THE BATTERIES IF NECESSARY, OR IN THE CASE OF MEMORY  
SPACE SHORTAGE DELETE CODES TO FREE SPACE.  
4. Press the key on the Niles R-6L or R-8L Hand-Held Learning Remote Control you wish  
to learn. The source key LED will blink rapidly for three seconds, indicating the remote  
is ready to learn.  
5. On the original remote, press and hold the key to be learned. Continue holding the  
key on the original remote until the R-6L or R-8L Hand-Held Learning Remote Control  
Source Key LED blinks twice.  
NOTE: IF THE SOURCE KEY LED DISPLAYS ONE LONG BLINK, A LEARNING ERROR HAS OCCURRED. TRY  
REPEATING THIS STEP AGAIN UNTIL A SUCCESSFUL CAPTURE IS OBTAINED. IF THE FUNCTION IS STILL NOT  
CAPTURED, PRESS AND HOLD SETUP TO EXIT PROGRAMMING AND REVIEW THE “LEARNING PRECAUTIONS”  
ABOVE. IF NEEDED, ALSO SEE “TROUBLESHOOTING”. AFTER REVIEW, START PROGRAMMING AGAIN AT STEP  
1.  
6. Repeat steps 4 through 5 for another key you would like to learn. Once you have  
completed learning all keys, press and hold SETUP until the source key LED blinks  
twice to save all data learned.  
DELETING A SINGLE LEARNED KEY  
This process returns the key to its original programming for the device you select. You can also  
delete learned programming by teaching a different function to the key (see “Programming a  
Learned Key”).  
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE REMOTE EXITS PROGRAMMING MODE.  
1. Press the source key from which you wish to remove the learned key  
2. Press and hold SETUP until the source key LED blinks twice, then release  
3. Enter 9 7 6. The source key LED blinks twice  
4. Press the key containing the learned function to be deleted twice. The source key LED  
blinks twice and the remote exits from programming mode  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
7
 
DELETING ALL LEARNED KEYS OF A SPECIFIC DEVICE  
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE REMOTE EXITS PROGRAMMING.  
1. Press and hold SETUP until the source key LED blinks twice, then release  
2. Press 9 7 6. The source key LED blinks twice  
3. Press a source key twice to clear all the learned keys for that device. The source key  
LED blinks twice and the remote exits from programming mode  
RESTORING KEY FUNCTIONS TO FACTORY SETTINGS  
1. Press and hold SETUP until a source key LED blinks twice, then release.  
2. Enter 9 8 0. A source key LED blinks twice.  
3. Press and hold SETUP until a source key LED blinks twice, then release.  
PROGRAMMING SEQUENCES  
Your Niles R-6L/R-8L Hand-Held Learning Remote Control includes the ability to program any  
key (other than the SETUP key) with a Sequence of functions. Each key can be set up to perform  
a pre-programmed set of sequential commands with the press of one key. A sequence can be  
used to control a home theater operation, to set a favorite channel, or for other multiple functions  
you would like to control with one key press. Moreover, each Sequence Key can hold up to 15  
commands. You can program a sequence that operates regardless of what device is selected, or  
one that only operates for a specific device.  
NOTE: PROGRAMMING A NEW SEQUENCE OVER AN EXISTING ONE ERASES THE ORIGINAL SEQUENCE.  
PROGRAMMING A DEVICE INDEPENDENT SEQUENCE  
1. Press and hold SETUP until a source key LED blinks twice, then release.  
2. Press 9 9 5. The source key LED blinks twice.  
3. Press the key to which you wish to assign a  
sequence.  
4. Enter the series of commands (key presses) you want the sequence to execute (up to  
15 commands).  
5. Press and hold SETUP until the source key LED blinks twice, then release.  
Now, when you press the preset sequence key, the remote sends the series of commands you have  
entered, regardless of what device is selected. For example, you could program a sequence key to  
turn on both your TV and cable box and select a particular channel. To clear the sequence, repeat  
8steps 1-5 above, but do not enter a series of commands at step 4.  
 
PROGRAMMING A DEVICE DEPENDENT SEQUENCE  
1. Press a source key.  
2. Press and hold SETUP until the source key LED blinks twice, then release.  
3. Press 9 7 8. The source key LED blinks twice.  
4. Press the key to which you wish to assign a sequence.  
5. Enter the series of commands (key presses) you want the sequence to execute (up to  
15 commands).  
6. Press and hold SETUP until the source key LED blinks twice, then release.  
Now, when you press the sequence key , the remote sends the series of commands you have  
entered, but only if the device selected in step 1 Is active. For example, you could program the  
sequence key to turn on both your TV and cable box and select a particular channel, but only if the  
TV is selected. If the DVD is selected, this key does not execute the sequence you set up for the TV.  
To clear the sequence, repeat steps 1-6 above, but do not enter a series of commands at step 5.  
TROUBLESHOOTING  
PROBLEM:  
1. LED does not blink when you press a key.  
SOLUTION:  
• Try pressing different keys. Replace the batteries with 2 new AA batteries  
PROBLEM:  
2. LED blinks when you press a key, but device does not respond.  
SOLUTION:  
• Make sure the remote is aimed at your device and is not more than 40 feet away  
PROBLEM:  
3. Source key LED blinks one long blink while in SETUP mode.  
SOLUTION:  
• An entry error has occurred (for example, wrong key). Try entering the sequence again  
PROBLEM:  
4. Remote does not control devices or commands are not working properly.  
SOLUTION:  
• Try all listed codes for the device. Make sure the device operates with an infrared remote  
control  
(CONTINUED ON NEXT PAGE)  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
9
 
PROBLEM:  
5. CH+, CH-, and LAST do not work for your RCA TV.  
SOLUTION:  
• Due to RCA design from 1983 to 1987, only the original remote control will operate these functions  
PROBLEM:  
6. Channels do not change properly when directly entering digits to change channels.  
SOLUTION:  
• If the original remote control required you to press Enter to change channels, press Enter  
on this remote after entering the channel number  
SPECIFICATIONS  
Transmitter: Infrared  
Signal Range: Approximately 15-30 Feet (4-10 Meters)  
Power Supply: Two “AA” batteries (1.5Vx2)  
LIMITED WARRANTY  
Niles Audio Corporation (“NILES”) warrants to the original retail purchaser only that this product  
will be free of manufacturing defects in material and workmanship for the following periods and  
subject to the limitations and exclusions set forth below:  
Lifetime Warranty  
All Passive Loudspeaker Products (those not requiring AC or battery power).  
Ten years from the date of purchase  
All Other Passive Products (those not requiring AC or battery power).  
Two years from the date of purchase  
All Active Products (those requiring AC or battery power).  
This warranty is not transferable to subsequent purchasers of the product. To obtain warranty  
service, contact the authorized dealer where you purchased your product or take the unit to the  
nearest authorized NILES dealer (with proof of purchase – claims made without proof of purchase  
will be denied) who will test the product and if necessary, forward it to NILES for service. If there  
are no authorized NILES dealers in your area, you must contact NILES to receive a factory Return  
Authorization Number. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN  
AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES.  
Upon examination, NILES will, at its sole option and expense, repair or replace any product found  
to be defective. NILES will return the repaired or replaced unit to you via its usual shipping method  
from the factory to your address in the United States of America or Canada only. Any shipping  
costs for addresses outside of the United States or Canada shall be the responsibility of the  
purchaser. In the event that this model is no longer available and cannot be repaired effectively,  
NILES, at its sole option, may replace it with a different model of equal or greater value, or refund  
the original purchase price paid. THE FOREGOING ARE YOUR EXCLUSIVE REMEDIES FOR  
BREACH OF WARRANTY.  
10  
 
This Warranty does not include service or parts to repair damage caused by improper use  
or handling, including but not limited to damage caused by accident, mishandling, improper  
installation, commercial use, abuse, negligence, or normal wear and tear, or any defect caused by  
repair to the product by anyone other than NILES.  
This warranty does not cover reimbursement for your costs of removing and transporting the  
product for warranty service evaluation, or installation of any replacement product provided under  
this warranty.  
This Warranty will be void if:  
• the Serial Number on the product has been removed, tampered with or defaced.  
• the product was not purchased from an authorized dealer or reseller.  
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND  
IMPLIED WARRANTIES. NILES EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES,  
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS  
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, WITH RESPECT TO THE PRODUCT.  
TO THE MAXIMUM EXTENT PERMITTED BY LAW, NILES SHALL NOT BE RESPONSIBLE FOR  
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE EXTENT PROVIDED (OR  
PROHIBITED) BY APPLICABLE LAW, EVEN IF NILES HAS BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss Warranty  
Act, or applicable state laws, then you may be entitled to any implied warranties allowed by law  
for the Warranty Period. Further, some states do not allow limitations on how long an implied  
warranty lasts or allow the exclusion or limitation of consequential damages, so such limitations  
may not apply to you. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
For the name of your nearest authorized NILES dealer, contact: NILES AUDIO CORPORATION,  
P.O. BOX 160818, Miami, Florida 33116-0818, or call 1-800-289-4434, 1-305-238-4373. Please  
be advised that NILES only sells its products via the Internet through a select group of authorized  
Internet through unauthorized Internet dealers are not covered by the NILES warranty and may be  
either:  
1) goods acquired on a secondary or grey market  
2) counterfeit or stolen goods  
3) damaged, or defective goods  
ATTENTION: TO OUR VALUED CONSUMERS:  
To insure that consumers obtain quality pre-sale and after-sale support and service, NILES  
products are sold exclusively through authorized dealers. This warranty is VOID if the products  
have been purchased from an unauthorized dealer.  
©2008 Niles Audio Corporation. All rights reserved. Niles, the Niles logos and Blending High Fidelity and Architecture  
are registered trademarks of Niles Audio Corporation. All other trademarks are the property of their respective owners.  
DS00606AWEB  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373  
11  
 

National Instruments Graphics Tablet NI PXI 5621 User Manual
NEC Telephone 17600SUG05 User Manual
Nikon Camcorder HN CP12 User Manual
Nikon Film Camera FG User Manual
Nokia Flat Panel Television AS191WM User Manual
OEM Systems Speaker RS 6B User Manual
One for All Universal Remote URC 3445 User Manual
Panasonic Cell Phone DMC TZ60 User Manual
Panasonic Digital Camera DMC FX500 User Manual
Panasonic Network Card 2SC5845 User Manual