Niles Audio Universal Remote TS120 User Manual

I N S T A L L A T I O N G U I D E  
TABLETOP IR SENSOR  
TS120  
 
INTROdUCTION  
The Niles TS120 is a tabletop infrared sensor designed for use with the Niles infrared extender  
systems.  
Installed in a remote room location, the TS120 receives the IR commands transmitted from your  
hand-held remote(s). The IR commands are carried via a CAT-5 cable to your A/V equipment in  
another room, and instantly “repeated”.  
The TS120 represents one of the 3 building blocks necessary to complete a Niles IR repeating  
system:  
IR Main System Unit—Models MSU140, MSU250, MSU480 and MSU440Z.  
®
IR Sensors/Keypads—Models WS120, TS120, MS120, MS220, CS120 and the IntelliPad .  
IR Flashers—Models MF1, MF1VF, MF2, MF2VF and the IRB1.  
An IR sensor expansion unit, Model IRH610, is available for IR repeater systems used in more than  
six rooms.  
CONTENTS  
Check that your TS120 Tabletop Infrared Sensor contains the following:  
• TS120  
• Removable Connector  
1
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
FEATURES ANd BENEFITS  
The TS120 offers a number of improvements over other tabletop IR sensors.  
• Wideband High-Fidelity Design enables operation with virtually any brand of equipment  
• Patent Pending Universal Noise Suppression Design enables operation in virtually any  
environment: near plasma and LCD displays, compact fluorescent lights, and indirect sunlight  
• Excellent IR receiving range—you get 20’ to 35’ of remote control range (depending upon the  
strength of your handheld remote)  
• Small size of only 2-7/8” wide x 1-1/16” high x 3-1/8 deep— fits almost anywhere.  
• Printed circuit board design uses surface mount technology, assuring high reliability  
• Ideal for both home and commercial installations  
• Non-skid, non-scratch feet  
• Two year parts and labor limited warranty  
2
 
INSTALLATION CONSIdERATIONS  
TypE OF CABLE  
The TS120 connects to the Niles infrared main system unit or IRH610 sensor expansion hub with an  
individual home run of CAT-5 cable. When running wires inside walls, most states and municipalities  
in the U.S. specify that you must use a special type of wire. Usually, the requirement is that the wire  
has a specific “CLre rating, such as “CL-2” or “CL-3”. Consult your Niles dealer, building contractor,  
or local building and inspection department if unsure about which type of wire is best for your  
application.  
TECH TIp: Wire size is expressed by it’s AWG (American Wire Gauge) number. The lower  
the AWG number, the larger the wire, i.e., 20 AWG wire is physically larger than 22 AWG.  
TS120 MOUNTING LOCATION  
The TS120 is ideal for use in applications when ceiling or wall-mounting is undesirable. Its small size  
and unobtrusive appearance makes it ideal for installation in existing homes or cabinets with great  
ease and minimal custom work. Installing the TS120 close to the primary location of the user will  
ensure best performance.  
The TS120 is designed to mount over or under almost any flat horizontal surface. Convenient  
mounting locations for the TS120 are:  
• On top of a television set  
• On a shelf in an entertainment center  
• Under a shelf in an entertainment center  
3
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
INSTALLATION CONSIdERATIONS (continued)  
RECEIvING RANGE ANd pICkUp ANGLE  
The receiving range of the TS120 will vary according to the IR output strength of the remote control  
being used. Remote strength varies among brands depending on the number and size of batteries  
used, and how many IR emitters the remote has. For example, remotes that operate on two small  
AAA batteries and have only one IR emitter are generally not as strong as remotes that use the  
larger AA size batteries and have two emitters. Tests with various manufacturers remote controls  
have shown that the operating range can vary from a minimum of 20’ to a maximum of about 35’.  
Infrared signals travel essentially line-of-sight. They will not pass through or around solid objects. Do  
not rely on an IR signal being able to “bounce” off a wall or object to the TS120. The IR pickup angle  
of the TS120 is 30° off-axis (horizontal and vertical) at 25’.  
AvOIdING ELECTRICAL INTERFERENCE  
Avoid locating the TS120 near any potential sources of electrical or optical noise, such as light  
dimmers, low-voltage lights, and neon lights.  
AvOIdING OpTICAL FEEdBACk  
If installing the TS120 in the same room as an IR flasher, it is possible for the flasher’s IR output  
to be picked-up by the TS120. This effect, known as an optical feedback loop, can cause erratic  
operation. Optical feedback is similar to acoustical feedback: the howling or whistling sound heard  
in a P.A. system when the microphone is too close to the speaker.  
To avoid optical feedback:  
1. Re-position the flasher(s) and/or the sensor.  
2. Use Niles MF series flashers and cover them with the supplied IR blockers.  
4
 
INSTALLATION CONSIdERATIONS (continued)  
AvOIdING INTERFERENCE  
TS120 is designed to work in most applications including with plasma and LCD TV’s and in areas  
where CFL lighting and indirect sunlight are present. You should avoid locating the TS120 near  
potential sources of electrical or optical noise, such as light dimmers or low-voltage lights.  
USING THE pOwER STATUS dISpLAy  
The Green power status LED can only be activated by a “power status” broadcast from a Niles IR  
main system unit (MSU140, MSU250, MSU480, MSU440Z). The IR main system unit will broadcast  
the power status signal if the preamp/ receiver is on and a 12V DC adapter is plugged into the  
preamp/receiver’s switched AC outlet and the 3.5mm plug is connected to the IR main system unit’s  
Status input jack (Figure 2).  
NOTE: THE 12V DC ADAPTER PLUGGED INTO THE SWITCHED OUTLET OF THE STEREO RECEIVER IS NOT  
INCLUDED WITH THE IR MAIN SYSTEM UNIT. IT SHOULD BE 12V DC WITH A MINIMUM OF 100MA OF  
OUTPUT. IT CAN BE ORDERED FROM YOUR NILES DEALER (FG01035 POWER ADAPTER).  
USING THE TS120 wITH NILES MULTIZONE kEypAdS wITH AN IR CONNECTION  
The TS120 is fully compatible with any Niles MultiZone Keypad with an IR connection, follow the  
wiring instructions in Figure 4. For specific information see your Niles MultiZone Keypad manual.  
5
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
INSTALLATION CONSIdERATIONS (continued)  
12V DC power supply  
(supplied with the  
Niles IR flasher  
Stereo receiver  
MSU250 IR main system  
unit) plugged into an  
unswitched AC outlet  
powers the system  
12V DC power supply  
(not supplied, Niles stock  
# FG01035) plugged into  
the switched outlet  
Bi-colored LED  
MSU250  
Removable  
Connector  
Pins  
Power, IR data, and power status signal  
via CAT-5 wire  
TS120 IR sensor  
Figure 2 Connecting the TS120 to a Niles MSU250 IR main  
system unit broadcasting a status feedback signal.  
Figure 1 Parts guide  
6
 
INSTALLATION  
STEp By STEp  
1. The TS120 is a small free-standing box designed to sit on a shelf or other convenient surface.  
®
The unit can be mounted under a shelf using double-sided tape or Velcro (not supplied).  
2. Run the cable to the TS120. Label the cable for future reference.  
3. Locate the connector on the TS120 and remove it.  
4. Next, strip 1/4” of insulation from the end of each wire. Tightly twist the end of each wire until  
there are no frayed ends.  
5. Use a small flathead screwdriver or your thumbnail to raise the locking tabs, exposing the holes  
on the removable connectors.  
Figure 4 This color code is based on the industry standard T568A coding for the RJ45  
connector. When connecting the TS120 to Niles MultiZone Keypads with an IR connection  
observe this pin configuration  
7
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
INSTALLATION (continued)  
6. Insert each wire into the appropriate hole on the removable connector plug (Figure 6), and snap  
the locking tab down. To help you, the connector plug is keyed. Insert the smooth side of the  
connector plug into the smooth side of the socket. Don’t force the scalloped side of the connector  
plug into the smooth side of the socket (Figure 5).  
7. Double-check all connections. Plug the connector back into its socket on the TS120.  
Figure 5 Installing the removable connector  
Figure 6 Removable Connector Plug  
8
 
OpERATION  
Operation of the TS120 is simple. Stand within the operational range of your TS120, aim your  
hand-held remote at the TS120 and press the button for the desired command. Your IR command is  
instantly repeated to your A/V equipment.  
GREEN “pOwER STATUS” LEd  
When the TS120 is correctly connected (Figure 2), the Green LED will stay lit as long as the pre-  
amp/receiver is on. When your preamp/receiver is off, the LED will stay off.  
BLUE “FEEdBACk” LEd  
The blue “feedback” LED on the TS120 visually confirms the reception of an IR command.  
9
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
TROUBLESHOOTING  
This manual contains instructions for the TS120 only. For specific information on the adjustment  
and operation of your Niles infrared extender system, please refer to the instruction manual included  
with your Niles IR Main System Unit (MSU140, MSU250, MSU480, MSU440Z).  
The bi-color blue/green LED on the front of the TS120 is a useful troubleshooting aid.  
The blue LED should light only when a remote command is being received. If the LED on the TS120  
“flickers”, and the TS120 functions normally, there is no cause for concern, some stray IR signal are  
being received by the TS120 but are not being repeated.  
1. Test the remote control(s) by operating the A/V equipment directly. Replace the batteries if  
needed.  
2. Double check the cable connections on all TS120’s and on the main system unit. Look for  
open, shorted or reversed wires.  
3. Test for interference from the following sources:  
• Neon, Compact Florecent Lighting (CFL), or halogen lights in the room  
• Light dimmers, beginning with those closest to the TS120  
Observe the TS120’s LED while performing all the tests. It is possible to have interference from  
more than one source.  
10  
 
TROUBLESHOOTING (continued)  
ELIMINATING OpTICAL FEEdBACk  
In some installations, two conditions combine to create an optical feedback loop. Symptoms can  
include poor range, intermittent operation or no operation.  
The conditions which sometimes combine to create a feedback loop are:  
1. Both a sensor and a flasher are located within the same room.  
2. There is some low-level noise or interference on your system.  
You can eliminate optical feedback by replacing any IRB1 “flooding flasher” with an MF1 or MF2  
MicroFlasher® and covering all flashers with the supplied IR blocking covers.  
IdENTIFyING THE TypE OF INTERFERENCE  
The blue “feedback” LED on the front of the TS120 is a useful troubleshooting aid.  
The LED should light blue only when a remote command is being received. However, if the LED on  
the TS120 “flickers”, and the TS120 functions normally, there is no cause for concern.  
If the TS120 does not work, and the LED does not light at all: Test the remote control(s) by operating  
the A/V equipment directly. Replace the batteries if needed. Double check the cable connections on  
the TS120’s and on the IR main system unit. Consult your IR main system unit’s manual for more  
detail.  
If the TS120 does not work, and the LED “flickers” or remains solidly lit: Cover up the Sensor with  
a piece of cardboard (your hand will actually create electromagnetic interference under some  
conditions). Observe the IR test LED.  
11  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
TROUBLESHOOTING (continued)  
IR TEST LEd OFF:  
Optical Interference  
IR TEST LEd ON OR FLICkERING:  
Electromagnetic and/or Optical Interference  
EMI (ELECTROMAGNETIC INTERFERENCE)  
Identify the source of the interference. The most common sources of electromagnetic interference  
are listed in the Installation Considerations section. To eliminate EMI try the following methods:  
1. Move the sensor or the sensor cable away from the EMI source or move the source of the EMI  
away from the sensor or the cable.  
2. Connect the Sensor’s GND terminal to true earth ground (if this isn’t feasible use the main  
system unit’s GND terminal).  
There are many methods for reducing interference. Which solution is best for you depends on your  
situation. If you require further assistance call Niles Technical Support at 305-238-4373 or  
1-800-289-4434 (M-F 8:00 AM - 7:00PM ET). You can also email Niles Technical Support at  
12  
 
SpECIFICATIONS  
IR System  
Compatible with virtually all brands of remotes using carrier frequencies  
between 25kHz and 90kHz  
IR Receiving Range  
20’ to 35’ depending upon the strength of the remote control  
IR Receiving Angle  
30° off-axis (horizontal and vertical) at 25’  
Mounting  
Tabletop  
Wiring Requirements  
Individual “home-runs” of CAT-5 cable  
Unit Dimensions  
2-7/8” wide x 1-1/16” high x 3-1/8” deep  
13  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
NOTES  
14  
 
NOTES  
15  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
LIMITEd wARRANTy  
Niles Audio Corporation (“NILES”) warrants its active products (those requiring AC or battery power) to the original purchaser to be free  
of manufacturing defects in material and workmanship for a period of two years from date of purchase.  
This Warranty is subject to the following additional conditions and limitations.The Warranty is void and inapplicable if NILES deems  
that the product has been used or handled other than in accordance with the instructions provided by the manufacturer, including  
but not limited to damage caused by accident, mishandling, improper installation, abuse, negligence, or normal wear and tear, or  
any defect caused by repair to the product by anyone other than NILES or an authorized NILES dealer.  
To obtain warranty service, take the unit to the nearest authorized NILES dealer, who will test the product and if necessary, forward  
it to NILES for service. If there are no authorized NILES dealers in your area, you must write to NILES and include your name,  
model and serial number of your unit, along with a brief description of the problem. A factory Return Authorization Number will  
be sent to you. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIPPING INSTRUCTIONS  
FROM NILES.  
If the above conditions are met, the purchaser’s sole remedy shall be to return the product to NILES, in which case NILES will  
repair or replace, at its sole option, the defective product without charge for parts or labor. NILES will return a unit repaired or  
replaced under warranty by shipping same by its usual shipping method from the factory (only) at its expense within the United  
States of America. THERE ARE NO OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION, EITHER EXPRESS OR IMPLIED  
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PRODUCT.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER/  
PURCHASER. NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE  
EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
For the name of your nearest authorized NILES dealer, contact:  
NILES AUDIO CORPORATION, P.O. BOX 160818, Miami, Florida 33116.  
Please fill in your product information and retain for your records.  
Model _______T__S_1_2_0________________  
Serial No. _________________________ Purchase Date ____________  
16  
 
wARRANTy REGISTRATION CARd  
TS120  
Model Purchased__________________________________ Serial Number __________________________  
Date Purchased (month/day/year)______________________ Dealer Name and Location _________________  
Dr.  
Name ____________________________________ Address _____________________________________  
City_______________________________State__________Zip ___________ Tel ( ) ____________  
Miss  
Mr.  
Mrs.  
Ms.  
Age:  
New Age  
R&B  
Popular  
Rock  
Myself  
Are there products/capabilities  
Under 25  
that you would like to see introduced?  
________________________  
________________________  
________________________  
________________________  
Which factor(s) influenced the purchase  
of your Niles product? (Please check  
all that apply)  
25-34  
Other ________________  
35-44  
How did you hear about Niles?  
45-54  
55 & over  
Architect/Developer  
Custom Installer  
Ease of Use  
Price/Value  
Income:  
Direct Mail  
Product Features  
Under $24,999  
Friend/Family  
In-Store Display  
Interior Designer  
Magazine Ad  
Mail-Order Catalog  
Newspaper Ad  
Product Brochure  
Product Review  
Retail Salesperson  
E-Tailer  
Quality/Durability  
$25,000-$44,999  
$45,000-$74,999  
$75,000-$99,999  
$100,000-$129,999  
Over $130,000  
Reputation  
Style/Appearance  
Warranty  
Do you . . . ?  
Own a House. If yes,  
Occupation:  
how many square feet?  
Arts/Entertainment  
Business Owner  
______________________  
Engineer  
Finance/Accounting  
What magazines do you read?  
1. _____________________  
2. _____________________  
3. _____________________  
Who will install the product?  
Own a Town House/  
General Office  
Condominium/Co-op  
Management  
Rent an Apartment  
Professional  
Sales/Marketing  
Student  
Rent a House  
Are you interested in receiving  
Tradesperson  
literature on other Niles products?  
Yes  
No  
Musical tastes: (Please check  
all that apply)  
Custom Installer  
Alternative  
Country  
Classical  
Jazz  
Electrician  
Friend  
17  
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 1-305-238-4373  
 
®
Bl e n d i n g Hi g H Fi d e l i t y An d Ar c H i t e c t u r e  
N i l e s A u d i o C o r p o r a t i o n  
1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6  
3 0 5 - 2 3 8 - 4 3 7 3  
1 - 8 0 0 - B u y - H i f i  
w w w . n i l e s a u d i o . c o m  
©2009 Niles Audio Corporation. All rights reserved. Niles, the Niles logos, IntelliPad, MicroFlasher and  
Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation.  
All other trademarks are the property of their respective owners. DS00674A  
 

Miele Vacuum Cleaner S 7000 User Manual
Miele Washer W3722 User Manual
Multiquip Septic System ST2037 User Manual
Niles Audio Speaker CM610 User Manual
Nortel Networks Camcorder 207344 B User Manual
Olympus DVR DM 20 DM 10 User Manual
Olympus Microcassette Recorder 142015 User Manual
Palm Cell Phone Z22 User Manual
Panasonic Headphones KX TD7580 User Manual
Panasonic Ventilation Hood ASEN9 User Manual